P ATENTS , C ONNECTIONS , A SSEMBLY , AND P ACKAGING
P ATENTS
Lamina’s light engines may be covered by pending patents and/or one or more of the following U.S. and/or
International patents 5876536, 6709749 B, 595880, 6017642, 5565262, 5681444, 5653834, 5581876, 5847935,
5514451, 5747931, 5925203, 5725808, 5929510, 5858145, 5866240, 5953203, 6055151, 614076, 6011330,
6399230, 6914501, 6168490, 6191934, 614075, 6160469, 6300267, 6471805, 6518502, 6739047, 6720859,
6759940, 6518502, 6670856 B1, 6720859, 6713862 B2, WO 00/47399, WO 00/26152, WO 98/19339, 5082804,
ZL99808762.9, 69623930, 69628549, 69629572, 805785, 69628549, 843621, 932500, 805785, 812258, 843621,
932500, 805785, 812258, 843621, 932500, 805785, 812258, 843621, 932500, 3327556, 3267299, 3226281,
3405545, 320630, 295695, 284068, 546471, 805785, 812258, 843621, 6455930, 6759940, 6713862, 7095053
7098483.
E LECTRICAL C ONNECTIONS
The LED light engines are available with or without Lamina’s EZ-Connect Board. EZ-Connect adapter boards have
AMP connectors for solderless connections to Lamina’s wiring harness.
As with many electrical devices, RMA type solder flux should be used to prepare the solder pads before application of
solder. Ensure proper strain relief of wires attached to the light engine to prevent damage to the light engines solder
pads. For more information refer to Lamina’s Connection application note AN-05 which can be found on the website
at www.laminalighting.com.
Functional test: Parts may be tested using a constant current source set at 25% of specified drive current specified
per specification, drawing or datasheet for no more than two seconds without heat sink. Voltage compliance of power
source should not exceed forward voltage plus 5 volts.
1.
2.
Optical and electrical specifications are given for the specified drive @ 25oC junction temperature.
When using constant current LED drivers with high compliance voltage (Advance, LEDworks, etc. or a custom
driver) the output of the supply must be connected to the part before power is applied to the input of the
supply.
A SSEMBLY R ECOMMENDATIONS
Lamina’s Light Engines are designed for attachment to a heat sink with conductive epoxy or thermal grease in the
joint. For attachment using screws, a 2-56 UNC round head or metric equivalent M2 X 0.4 cheese head screw, 18-8
SS is recommended. When mounting the light engine, position the three screws in the center of each of the three
slots. Tighten the three screws evenly, first to about 0.89 inch pounds (10 Newton-centimeter), and then tighten each
to a maximum torque of 4 inch pounds (45 Newton-centimeter). Flatness requirement of the surface that the light
engine is mounted to is 0.001 inch/inch (1mm/meter).
P ACKAGING - R ECEIVING P ARTS AND P ACKAGING T RAYS
Your parts will arrive in either custom fitted trays or bulk packaging when appropriate. This packaging was designed
or specified to provide the necessary protection during shipment and to take up the least amount of space in your
storage area.
N OTES
1. These products use silicone materials for superior optical performance. Do not expose the part to fluids that
may react with silicone compounds. See Dow Chemical Form 45-0113D-01, Silicone Fluid Resistance Guide.
2.
3.
4.
Ray trace models are available upon request.
Lamina ? may make process or materials changes affecting the performance or other characteristics of our
products. The products supplied after such changes will continue to meet published specifications, but may
not be identical to product supplied as samples or under prior orders.
All specifications are based on mounting the LED array to a heat sink using the specified hardware and
thermal grease (e.g. Wakefield P/N 120). The heat sink must meet the specified flatness requirement.
Mounting using screws and thermal tape may damage the device.
120 Hancock Lane | Westampton, NJ 08060 | info@laminalighting.com | +1.609.265.1401 | 1.800.808.5822
?2008 L AMINA L IGHTING I NCORPORATED
L IGHT E NGINE A CCESSORIES FM-0169 R EV 05.21.08
L IGHT E NGINE
A CCESSORIES
  
相关PDF资料
EZLC-4421 LB KIT EZLINK F930/SI4421 LOW BAND
F2M03G-KIT-1 KIT EVAL G MOD SNGL (NO OEM BRD)
F2M03M-KIT-1 KIT EVAL M MOD SNGL (NO OEM BRD)
FA10323_K2S-W LENS FOR LUXEON K2
FA10539_SSS-W LENS FOR SEOUL P4
FA10643_TINA-M LENS FOR GOLDEN/PLATINUM DRAGON
FA10644_TINA-D LENS TINA DIFF 6.5DEG
FA10666_CXP-D LENS CXP DIFF SQ 16DEG
相关代理商/技术参数
EZ-400-716M-RAX 制造商:TIMES MICROWAVE 功能描述:TIMES MICROWAVE LMR400 DIN MALE RIGHT ANGEL
EZ-400-NF 制造商:TIMES MICROWAVE 功能描述:TYPE-N FEMALE JACK 50 OHM CRIMP SLEEVE
EZ-400-NF/BH 制造商:TIMES MICROWAVE 功能描述:COAX CABLE CONNECTOR
EZ-400-NM-75 制造商:TIMES MICROWAVE 功能描述:CONNECTOR
EZ-400-NMC-2D 制造商:TIMES MICROWAVE 功能描述:EZ-400-NMC-2D
EZ400NMH 制造商:TMS 功能描述:
EZ-400-NMH-D 制造商: 功能描述: 制造商:undefined 功能描述:
EZ400NMHRA 制造商:TIMES MICROWAVE 功能描述:RIGHT ANGLE CONNECTOR